![]() Time: analog, push the time of the current song being played. Pushing 0 will set the player in "streaming" mode. Title: text, push the title of the current song being played.Īlbum: text, push the album of the current song being played.Īrtist: text, push the album of the current song being played.ĭuration: analog, push the duration, in seconds, of the current song being played. You have access to the following outputs: After importing them, and before anything else, you will have to configure the IP of the LoxBerry, replacing by the real IP. Virtual outputs: those will let you inform the plugin about data needed by the player. Repeat: analog, represents the repeating state ( 0 = do not repeat, 1 = repeat one song, 2 = repeat playlist). Shuffle: analog, represents the shuffling state ( 0 = not active, 1 = active). Queue index: analog, represents the position in the queue, as 0 -based index. Time: analog, represents the current time set by the user, in seconds (e.g. Volume: analog, represents the volume set by the user on a range. Pause: digital, will emit a pulse when pausing. Play: digital, will emit a pulse when starting to play. Virtual inputs: those will let you know when something happens in a zone, triggered by the user. ![]() You can download templates for both of them from the configuration page. Now it's time to bring in the virtual inputs and outputs to be able to act on them. After rebooting you should get the zone as connected, with the player stopped. Set as its address, where 192.168.1.2 is the IP address of the LoxBerry.ĭrag the first zone of the Music Server and make it visible in the UI. Head to the Loxone Config, and add a Music Server (Audio/Add Audio Server/Loxone Music Server/Loxone Music Server x Zones). Installationĭownload and install the ZIP file and restart the LoxBerry.Ĭonfigure the amount of music servers you want, and their zones. While this may seem to be a tricky setup, it enables users to configure whatever action they want when the user clicks play, pause, etc. The Music Server interface provides virtual inputs and outputs into the Loxone Miniserver, from which you can act based on the different actions provided by the Music Zone interface. Each fake music server can be configured with an arbitrary number of zones. Fake music servers are created in different ports of the LoxBerry, starting at port 6091. This plugin provides a fake music server that the Loxone Miniserver can connect to. Some help is also welcome, especially in the Virtual IO and the Web interface parts. Please report bugs through the GitHub interface. ![]() ![]() As such we would normally not recommend using a music system for processing of TV audio.Note: right now the plugin is in a very early phase of development, and it's currently unstable. There is no ability for adjusting the delay on the Music server to compensate, also please bear in mind that different sources e.g Blu-Ray, Sky etc… will have different processing delays. If the audio is before the video you will have to see if the video processing delay can be reduced on the TV side, if the audio is after the video you will have to see if there is an audio delay option on the TV. The second issue with delay will always be present as the Music server has to process the audio, plus as you are using a digital output from the TV, through a DAC this would have also be subject to a processing delay. If the audio line level drop is due to voltage drop lower than line level then a pre-amp should help to rectify this part of the problem. The likely reason that it worked on the Marantz unit is that this is probably an integrated amplifier with a built in pre-amp on the line in. The cause of your low to none existent audio on the line ins is very likely due to a drop in the line level due to the amount of conversion happening from your source. Is there any way to increase the audio level of Line 1 or Line 2, and also reduce the delay ? The other issue we noted is that when using Line 2, there is quite a large amount of delay in the audio processing, so the sound lags picture by a second or two. I have also tried the Line 1 input, and there is no TV sound, just a small amount of "noise". Please note that I tried this setup at home first, feeding the output of the DAC into my Marantz stereo amplifier and it worked perfectly. When "Line 2" is selected on the app, we can hear very faint TV sound through the ceiling speakers, but only when the volume level is set to 100%. At the hub I feed the coaxial audio into a DAC and have connected the stereo phono out from the DAC into "Line 2" on the Loxone miniserver. I have managed to convert the TV optical audio out to coaxial audio and send it via a Cat 6 cable between the TV room and the Loxone "hub". A client has asked me if I can sort out a TV audio feed into his Loxone audio system so that he can play his TV sound through the ceiling speakers in his room.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |